Plumbing With PEX » Field Controls

8' Wiring Harness for GVD Dampers [FCU-8]

pexsupply111125 — Fri, 25 Nov 2011 01:47:37 +0000

Product: 8' Wiring Harness for GVD Dampers
Manufacturer: Field Controls

Part Number: FCU-8

Price: $14.85

Free Shipping Eligible: No
Description: The Field Vent Damper works automatically to allow natural draft during appliance operation while preventing residual appliance heat and conditioned air from escaping during off cycles. It also prevents the infiltration of cold air during down drafts.
Safety Features

Dual safety switches allow the burner to fire only when the damper is in the open position. This unit will not interfere with existing appliance safety controls, when properly installed.

Operational Features

Operates with all 24 VAC, 60hz intermittent ignition and standing pilot ignition systems.
Stainless steel construction provides superior corrosion resistance.
Damper operation: power opens in 15 seconds, power closes in 15 seconds. Power is off at damper motor when it is at rest.
Hold open switch allows damper to be placed in an open position and taken out of service to assist with trouble shooting appliance problems.
Keyed wiring harness connector plug installs only one way, preventing incorrect wiring connection.

How the GVD Works

The Field Vent Damper is installed in the vent pipe, after the draft hood, or barometric. During off cycles, it remains closed, preventing air flow through the vent. When there is a call for heat, the motor is energized, rotating the damper 90 degrees to an open position. Opening and closing takes approximately 15 seconds. When the damper is fully open, the burner is allowed to fire and flue gases pass freely through the vent. When the thermostat is satisfied, the burner stops, and the damper automatically closes. For service and trouble shooting, the damper can be locked in the open position.

Electrical Specifications

Minimum wiring requirements: 24 VAC – 18 gauge – 105 degrees C
Power requirements: 3 watts at 24 VAC, 60 Hz, when opening or closing

10-inch Automatic GVD Vent Damper [GVD-10PL]

pexsupply111125 — Fri, 25 Nov 2011 01:47:37 +0000

Product: 10-inch Automatic GVD Vent Damper
Manufacturer: Field Controls

Part Number: GVD-10PL

Price: $146.95

Free Shipping Eligible: No
Description: The Field Vent Damper works automatically to allow natural draft during appliance operation while preventing residual appliance heat and conditioned air from escaping during off cycles. It also prevents the infiltration of cold air during down drafts.
Safety Features

Dual safety switches allow the burner to fire only when the damper is in the open position. This unit will not interfere with existing appliance safety controls, when properly installed.

Operational Features

Operates with all 24 VAC, 60hz intermittent ignition and standing pilot ignition systems.
Stainless steel construction provides superior corrosion resistance.
Damper operation: power opens in 15 seconds, power closes in 15 seconds. Power is off at damper motor when it is at rest.
Hold open switch allows damper to be placed in an open position and taken out of service to assist with trouble shooting appliance problems.
Keyed wiring harness connector plug installs only one way, preventing incorrect wiring connection.

Dimensions

Pipe Size: 10"
Length: 12-1/8"
Height: 14-7/8"
Clearance: 4"
Exposed Pipe: 10-7/8"

How the GVD Works

The Field Vent Damper is installed in the vent pipe, after the draft hood, or barometric. During off cycles, it remains closed, preventing air flow through the vent. When there is a call for heat, the motor is energized, rotating the damper 90 degrees to an open position. Opening and closing takes approximately 15 seconds. When the damper is fully open, the burner is allowed to fire and flue gases pass freely through the vent. When the thermostat is satisfied, the burner stops, and the damper automatically closes. For service and trouble shooting, the damper can be locked in the open position.

Electrical Specifications

Minimum wiring requirements: 24 VAC – 18 gauge – 105 degrees C
Power requirements: 3 watts at 24 VAC, 60 Hz, when opening or closing

12-inch Automatic GVD Vent Damper [GVD-12PL]

pexsupply111125 — Fri, 25 Nov 2011 01:47:37 +0000

Product: 12-inch Automatic GVD Vent Damper
Manufacturer: Field Controls

Part Number: GVD-12PL

Price: $156.95

Free Shipping Eligible: No
Description: The Field Vent Damper works automatically to allow natural draft during appliance operation while preventing residual appliance heat and conditioned air from escaping during off cycles. It also prevents the infiltration of cold air during down drafts.
Safety Features

Dual safety switches allow the burner to fire only when the damper is in the open position. This unit will not interfere with existing appliance safety controls, when properly installed.

Operational Features

Operates with all 24 VAC, 60hz intermittent ignition and standing pilot ignition systems.
Stainless steel construction provides superior corrosion resistance.
Damper operation: power opens in 15 seconds, power closes in 15 seconds. Power is off at damper motor when it is at rest.
Hold open switch allows damper to be placed in an open position and taken out of service to assist with trouble shooting appliance problems.
Keyed wiring harness connector plug installs only one way, preventing incorrect wiring connection.

Dimensions

Pipe Size: 12"
Length: 12-1/8"
Height: 16-7/8"
Clearance: 4"
Exposed Pipe: 10-7/8"

How the GVD Works

The Field Vent Damper is installed in the vent pipe, after the draft hood, or barometric. During off cycles, it remains closed, preventing air flow through the vent. When there is a call for heat, the motor is energized, rotating the damper 90 degrees to an open position. Opening and closing takes approximately 15 seconds. When the damper is fully open, the burner is allowed to fire and flue gases pass freely through the vent. When the thermostat is satisfied, the burner stops, and the damper automatically closes. For service and trouble shooting, the damper can be locked in the open position.

Electrical Specifications

Minimum wiring requirements: 24 VAC – 18 gauge – 105 degrees C
Power requirements: 3 watts at 24 VAC, 60 Hz, when opening or closing

4-inch Automatic GVD Vent Damper [GVD-4PL]

pexsupply111125 — Fri, 25 Nov 2011 01:47:37 +0000

Product: 4-inch Automatic GVD Vent Damper
Manufacturer: Field Controls

Part Number: GVD-4PL

Price: $96.55

Free Shipping Eligible: No
Description: The Field Vent Damper works automatically to allow natural draft during appliance operation while preventing residual appliance heat and conditioned air from escaping during off cycles. It also prevents the infiltration of cold air during down drafts.
Safety Features

Dual safety switches allow the burner to fire only when the damper is in the open position. This unit will not interfere with existing appliance safety controls, when properly installed.

Operational Features

Operates with all 24 VAC, 60hz intermittent ignition and standing pilot ignition systems.
Stainless steel construction provides superior corrosion resistance.
Damper operation: power opens in 15 seconds, power closes in 15 seconds. Power is off at damper motor when it is at rest.
Hold open switch allows damper to be placed in an open position and taken out of service to assist with trouble shooting appliance problems.
Keyed wiring harness connector plug installs only one way, preventing incorrect wiring connection.

Dimensions

Pipe Size: 4"
Length: 6-1/16"
Height: 8-7/8"
Clearance: 15/16"
Exposed Pipe: 4-13/16"

How the GVD Works

The Field Vent Damper is installed in the vent pipe, after the draft hood, or barometric. During off cycles, it remains closed, preventing air flow through the vent. When there is a call for heat, the motor is energized, rotating the damper 90 degrees to an open position. Opening and closing takes approximately 15 seconds. When the damper is fully open, the burner is allowed to fire and flue gases pass freely through the vent. When the thermostat is satisfied, the burner stops, and the damper automatically closes. For service and trouble shooting, the damper can be locked in the open position.

Electrical Specifications

Minimum wiring requirements: 24 VAC – 18 gauge – 105 degrees C
Power requirements: 3 watts at 24 VAC, 60 Hz, when opening or closing

5-inch Automatic GVD Vent Damper [GVD-5PL]

pexsupply111125 — Fri, 25 Nov 2011 01:47:37 +0000

Product: 5-inch Automatic GVD Vent Damper
Manufacturer: Field Controls

Part Number: GVD-5PL

Price: $97.75

Free Shipping Eligible: No
Description: The Field Vent Damper works automatically to allow natural draft during appliance operation while preventing residual appliance heat and conditioned air from escaping during off cycles. It also prevents the infiltration of cold air during down drafts.
Safety Features

Dual safety switches allow the burner to fire only when the damper is in the open position. This unit will not interfere with existing appliance safety controls, when properly installed.

Operational Features

Operates with all 24 VAC, 60hz intermittent ignition and standing pilot ignition systems.
Stainless steel construction provides superior corrosion resistance.
Damper operation: power opens in 15 seconds, power closes in 15 seconds. Power is off at damper motor when it is at rest.
Hold open switch allows damper to be placed in an open position and taken out of service to assist with trouble shooting appliance problems.
Keyed wiring harness connector plug installs only one way, preventing incorrect wiring connection.

Dimensions

Pipe Size: 5"
Length: 6-1/16"
Height: 9-7/8"
Clearance: 15/16"
Exposed Pipe: 4-13/16"

How the GVD Works

The Field Vent Damper is installed in the vent pipe, after the draft hood, or barometric. During off cycles, it remains closed, preventing air flow through the vent. When there is a call for heat, the motor is energized, rotating the damper 90 degrees to an open position. Opening and closing takes approximately 15 seconds. When the damper is fully open, the burner is allowed to fire and flue gases pass freely through the vent. When the thermostat is satisfied, the burner stops, and the damper automatically closes. For service and trouble shooting, the damper can be locked in the open position.

Electrical Specifications

Minimum wiring requirements: 24 VAC – 18 gauge – 105 degrees C
Power requirements: 3 watts at 24 VAC, 60 Hz, when opening or closing

6-inch Automatic GVD Vent Damper [GVD-6PL]

pexsupply111125 — Fri, 25 Nov 2011 01:47:37 +0000

Product: 6-inch Automatic GVD Vent Damper
Manufacturer: Field Controls

Part Number: GVD-6PL

Price: $98.95

Free Shipping Eligible: No
Description: The Field Vent Damper works automatically to allow natural draft during appliance operation while preventing residual appliance heat and conditioned air from escaping during off cycles. It also prevents the infiltration of cold air during down drafts.
Safety Features

Dual safety switches allow the burner to fire only when the damper is in the open position. This unit will not interfere with existing appliance safety controls, when properly installed.

Operational Features

Operates with all 24 VAC, 60hz intermittent ignition and standing pilot ignition systems.
Stainless steel construction provides superior corrosion resistance.
Damper operation: power opens in 15 seconds, power closes in 15 seconds. Power is off at damper motor when it is at rest.
Hold open switch allows damper to be placed in an open position and taken out of service to assist with trouble shooting appliance problems.
Keyed wiring harness connector plug installs only one way, preventing incorrect wiring connection.

Dimensions

Pipe Size: 6"
Length: 6-1/2"
Height: 10-7/8"
Clearance: 1-3/16"
Exposed Pipe: 5-1/4"

How the GVD Works

The Field Vent Damper is installed in the vent pipe, after the draft hood, or barometric. During off cycles, it remains closed, preventing air flow through the vent. When there is a call for heat, the motor is energized, rotating the damper 90 degrees to an open position. Opening and closing takes approximately 15 seconds. When the damper is fully open, the burner is allowed to fire and flue gases pass freely through the vent. When the thermostat is satisfied, the burner stops, and the damper automatically closes. For service and trouble shooting, the damper can be locked in the open position.

Electrical Specifications

Minimum wiring requirements: 24 VAC – 18 gauge – 105 degrees C
Power requirements: 3 watts at 24 VAC, 60 Hz, when opening or closing

7-inch Automatic GVD Vent Damper [GVD-7PL]

pexsupply111125 — Fri, 25 Nov 2011 01:47:37 +0000

Product: 7-inch Automatic GVD Vent Damper
Manufacturer: Field Controls

Part Number: GVD-7PL

Price: $103.95

Free Shipping Eligible: No
Description: The Field Vent Damper works automatically to allow natural draft during appliance operation while preventing residual appliance heat and conditioned air from escaping during off cycles. It also prevents the infiltration of cold air during down drafts.
Safety Features

Dual safety switches allow the burner to fire only when the damper is in the open position. This unit will not interfere with existing appliance safety controls, when properly installed.

Operational Features

Operates with all 24 VAC, 60hz intermittent ignition and standing pilot ignition systems.
Stainless steel construction provides superior corrosion resistance.
Damper operation: power opens in 15 seconds, power closes in 15 seconds. Power is off at damper motor when it is at rest.
Hold open switch allows damper to be placed in an open position and taken out of service to assist with trouble shooting appliance problems.
Keyed wiring harness connector plug installs only one way, preventing incorrect wiring connection.

Dimensions

Pipe Size: 7"
Length: 7-1/16"
Height: 11-7/8"
Clearance: 1-7/16"
Exposed Pipe: 5-13/16"

How the GVD Works

The Field Vent Damper is installed in the vent pipe, after the draft hood, or barometric. During off cycles, it remains closed, preventing air flow through the vent. When there is a call for heat, the motor is energized, rotating the damper 90 degrees to an open position. Opening and closing takes approximately 15 seconds. When the damper is fully open, the burner is allowed to fire and flue gases pass freely through the vent. When the thermostat is satisfied, the burner stops, and the damper automatically closes. For service and trouble shooting, the damper can be locked in the open position.

Electrical Specifications

Minimum wiring requirements: 24 VAC – 18 gauge – 105 degrees C
Power requirements: 3 watts at 24 VAC, 60 Hz, when opening or closing

8-inch Automatic GVD Vent Damper [GVD-8PL]

pexsupply111125 — Fri, 25 Nov 2011 01:47:37 +0000

Product: 8-inch Automatic GVD Vent Damper
Manufacturer: Field Controls

Part Number: GVD-8PL

Price: $119.95

Free Shipping Eligible: No
Description: The Field Vent Damper works automatically to allow natural draft during appliance operation while preventing residual appliance heat and conditioned air from escaping during off cycles. It also prevents the infiltration of cold air during down drafts.
Safety Features

Dual safety switches allow the burner to fire only when the damper is in the open position. This unit will not interfere with existing appliance safety controls, when properly installed.

Operational Features

Operates with all 24 VAC, 60hz intermittent ignition and standing pilot ignition systems.
Stainless steel construction provides superior corrosion resistance.
Damper operation: power opens in 15 seconds, power closes in 15 seconds. Power is off at damper motor when it is at rest.
Hold open switch allows damper to be placed in an open position and taken out of service to assist with trouble shooting appliance problems.
Keyed wiring harness connector plug installs only one way, preventing incorrect wiring connection.

Dimensions

Pipe Size: 8"
Length: 8-1/16"
Height: 12-7/8"
Clearance: 1-15/16"
Exposed Pipe: 6-13/16"

How the GVD Works

The Field Vent Damper is installed in the vent pipe, after the draft hood, or barometric. During off cycles, it remains closed, preventing air flow through the vent. When there is a call for heat, the motor is energized, rotating the damper 90 degrees to an open position. Opening and closing takes approximately 15 seconds. When the damper is fully open, the burner is allowed to fire and flue gases pass freely through the vent. When the thermostat is satisfied, the burner stops, and the damper automatically closes. For service and trouble shooting, the damper can be locked in the open position.

Electrical Specifications

Minimum wiring requirements: 24 VAC – 18 gauge – 105 degrees C
Power requirements: 3 watts at 24 VAC, 60 Hz, when opening or closing

9-inch Automatic GVD Vent Damper [GVD-9PL]

pexsupply111125 — Fri, 25 Nov 2011 01:47:37 +0000

Product: 9-inch Automatic GVD Vent Damper
Manufacturer: Field Controls

Part Number: GVD-9PL

Price: $139.95

Free Shipping Eligible: No
Description: The Field Vent Damper works automatically to allow natural draft during appliance operation while preventing residual appliance heat and conditioned air from escaping during off cycles. It also prevents the infiltration of cold air during down drafts.
Safety Features

Dual safety switches allow the burner to fire only when the damper is in the open position. This unit will not interfere with existing appliance safety controls, when properly installed.

Operational Features

Operates with all 24 VAC, 60hz intermittent ignition and standing pilot ignition systems.
Stainless steel construction provides superior corrosion resistance.
Damper operation: power opens in 15 seconds, power closes in 15 seconds. Power is off at damper motor when it is at rest.
Hold open switch allows damper to be placed in an open position and taken out of service to assist with trouble shooting appliance problems.
Keyed wiring harness connector plug installs only one way, preventing incorrect wiring connection.

Dimensions

Pipe Size: 9"
Length: 10-1/8"
Height: 13-7/8"
Clearance: 3"
Exposed Pipe: 8-7/8"

How the GVD Works

The Field Vent Damper is installed in the vent pipe, after the draft hood, or barometric. During off cycles, it remains closed, preventing air flow through the vent. When there is a call for heat, the motor is energized, rotating the damper 90 degrees to an open position. Opening and closing takes approximately 15 seconds. When the damper is fully open, the burner is allowed to fire and flue gases pass freely through the vent. When the thermostat is satisfied, the burner stops, and the damper automatically closes. For service and trouble shooting, the damper can be locked in the open position.

Electrical Specifications

Minimum wiring requirements: 24 VAC – 18 gauge – 105 degrees C
Power requirements: 3 watts at 24 VAC, 60 Hz, when opening or closing

4-inch Oil Vent Damper [OVD-4]

pexsupply111125 — Fri, 25 Nov 2011 01:47:37 +0000

Product: 4-inch Oil Vent Damper
Manufacturer: Field Controls

Part Number: OVD-4

Price: $154.95

Free Shipping Eligible: No
Description: Benefits

Reduces heating bill
Improves efficiency
Increases comfort
Reduces off-cycle heat loss

Features

Available in sizes 4"– 8"
Blocked vent safety switch included
Automatic power open/power close
Two internal safety switches
Flex seal provides self cleaning action
Hold open service switch
Stainless steel construction
CSA listed
(Listed to UL-17 Standard and CSA B140.14)